Belt Dryers for Biomass & Agricultural Residues

Wood chips · Sawdust · Agricultural residues

Quick answer

Meshotherm mesh belt dryers take wood chips, sawdust, agro residues and RDF from 40–55% moisture down to the 10–15% that pellet mills, gasifiers and cement kilns need, for plants up to 500 t/day. Drying RDF from 40% to 15% lifts its energy per tonne by about half.

Typical duty

Wet feedUp to 500 t/day
Moisture in → out40–55% → 10–15%
MaterialsWood chips, sawdust, agro residues, RDF/SRF
Heat sourcesFlue gas, biomass hot air, process waste heat
PlatformMeshotherm mesh belt dryer

GEM DRYTECH · INDUSTRIAL BELT DRYING

Prepare biomass for the next stage of your process with a belt drying system selected around your feed, moisture target and available heat. Gem Drytech Systems LLP manufactures industrial dryers in India and offers pilot drying trials.

Get a dryer selection & budget quotation   Explore pilot trials


Wood chip, sawdust and RDF dryers for pellet and fuel plants

Meshotherm® mesh belt dryers dry wood chips, sawdust, bark, agro residues and RDF to the moisture pellet mills, boilers, kilns and waste-to-energy plants need, typically around 10–15% for pelletising. Belt drying runs at low to medium air temperatures, so recovered heat from boilers, engines or flue gas can carry much of the load.

Lower moisture raises the usable energy per tonne of fuel and cuts freight weight. Share your throughput, inlet moisture and heat source for a pilot trial and sizing.

Biomass materials and applications

Discuss wood chips, sawdust, bagasse, husks and other agricultural residues with our engineering team. Drying requirements vary with particle size, bulk density, initial moisture and the intended downstream process, including storage, fuel preparation or pellet production.

Continuous belt drying

Material is distributed across a moving belt and passes through a chamber supplied with heated air. Belt speed, bed depth, airflow and temperature influence moisture removal. The feed preparation and distribution system must suit the material.

Design around the downstream process

Share the moisture specification required by your pellet mill, storage system or other downstream equipment. We assess wet throughput, operating hours and moisture reduction together, so the proposed dryer addresses the duty rather than a nominal feed rate alone.

Heat source and material handling

Discuss steam, thermal oil, hot-air generation or electric heating against your available utilities. Fine particles, dust management, cleaning, fire risk assessment and discharge handling need to be considered as part of the overall project.

Evaluate your sample

A representative sample helps assess drying behaviour, particle handling and operating conditions. Pilot results and project information support equipment selection and a process proposal. Ask about the pilot-trial programme before final sizing.

Your material. Your process.

These are examples of applications, not a complete list. For other materials, see our mesh belt dryer, band dryer and full dryer range, or discuss your requirement with us.

Frequently asked questions

Can a belt dryer prepare biomass for pellet production?

It can be evaluated for moisture reduction before pellet production. The target moisture and material preparation must match the requirements of the downstream pellet process.

Can wood chips and sawdust use the same settings?

Not necessarily. Particle size, bed permeability, bulk density and moisture differ, so feed distribution and operating settings must be assessed for each material.

What should I send for a proposal?

Include the following in your enquiry:

  • Feed: biomass type, particle-size range, bulk density and wet-feed rate in kg/hour.
  • Moisture: inlet and target values with the measurement basis, including expected seasonal variation.
  • Operation: operating hours, available heat source and utility temperatures.
  • Site: installation country, space constraints and storage arrangements.
  • Product destination: the requirements of the pellet mill, fuel process or other downstream equipment.

Mark estimates clearly and use the quotation form below to share the information available. Discuss a representative sample and pilot-trial arrangements with GEM before dispatch.

Get a dryer selection & budget quotation

Tell us what you need to dry, your required capacity and installation country. Share inlet and target moisture, available heat and project timing if known. Estimates are welcome; write “not sure” where you need guidance. Our team can review suitable dryer options and the information needed for a budget quotation. Final selection and pricing depend on your material and project requirements.

    Prefer to discuss first? WhatsApp +91 98311 73874 or contact Gem Drytech.

    Biomass project evidence: sawdust rotary drying

    Our 3,000 kg/hour sawdust drying case study describes a rotary dryer system in Kolkata with a firewood-fired brick furnace. It provides a published biomass reference with project-specific feed and moisture results.

    Discuss this example alongside the belt-drying approach described on this page. A belt dryer proposal must be assessed separately for your feed properties, moisture duty and heat supply. Share your biomass requirements or discuss a pilot trial.

    Chat with GEM Drytech on WhatsApp