GEM DRYTECH · INDUSTRIAL BELT DRYING
Plan a continuous drying process around your sludge, available heat and required final moisture. Gem Drytech Systems LLP manufactures industrial drying equipment in India and offers pilot drying trials to help evaluate your material.
Get a dryer selection & budget quotation Explore pilot trials
Industrial sludge dryer: stop paying to haul water
Dewatered sludge and filter cake typically leave the press at 70–85% moisture, and disposal is charged per wet tonne. As an illustration, drying 20 t/day of cake at 80% moisture to 10% leaves about 4.4 t/day, so roughly 15.6 t/day of water no longer travels to the landfill, TSDF or co-processing site. Your own disposal rate decides the saving.
As a sludge dryer manufacturer, Gem Drytech supplies Meshotherm® mesh belt and Beltotherm® belt dryers for ETP sludge, filter cake, paper mill sludge, textile and pharmaceutical sludge, and municipal biosolids. Low-temperature belt drying can run on waste heat, steam or biogas available on site.
Municipal and industrial sludge applications
Discuss dewatered sewage sludge, biosolids, wastewater treatment sludge, ETP sludge and paper mill sludge with our engineering team. Each feed requires its own assessment: solids content, consistency, contaminants and intended use influence the equipment and process.
How belt drying works
A controlled layer of material travels through a drying chamber on a moving belt. Heated air removes moisture while belt speed, airflow and temperature are adjusted for the material. Feed preparation and even distribution are important to a consistent drying result.
What we assess before sizing
We review wet-feed rate, operating hours, inlet dry-solids content or moisture, target moisture, particle or cake characteristics, available heat source and site conditions. Sludge handling, odour control, exhaust treatment and cleaning requirements should be defined with the project team.
Heating and process options
Discuss steam, thermal oil, hot-air generation or electric heating against your site utilities. The proposed configuration, construction materials, controls and upstream or downstream equipment depend on the feed assessment and project requirements.
Pilot trials before a final equipment decision
A representative sample can help assess drying behaviour, handling and achievable moisture under trial conditions. Ask about sample requirements and the pilot-trial programme. Trial results and project data inform the proposal; this page does not specify a guaranteed capacity or final moisture.
Your material. Your process.
These are examples of applications, not a complete list. For other materials, see our mesh belt dryer, band dryer and full dryer range, or discuss your requirement with us.
Frequently asked questions
Can one sludge dryer handle every type of sludge?
No. Sludge properties vary. Share the sludge source, solids content, contaminants and handling characteristics so suitability can be assessed.
Can drying alone guarantee safe disposal or reuse?
No. The intended outlet, local requirements and any treatment or emissions controls must be assessed separately. A moisture-reduction target alone does not establish suitability for reuse.
What information is needed for a quotation?
Include the following in your enquiry:
- Feed: sludge source, dewatering method, wet throughput in kg/hour and operating hours.
- Moisture: inlet and target values, with the measurement basis stated; include available sludge analysis.
- Handling: cake or particle characteristics, stickiness and representative sample availability.
- Site: installation country, available heat source and relevant site constraints.
- Project requirements: intended use of the dried material, odour and exhaust treatment, cleaning and downstream handling.
Mark estimates clearly and use the quotation form below to share the information you have. Discuss sample arrangements with GEM before dispatch.
Preparing your project data? Use the wastewater project data checklist. When comparing proposals, see the sludge dryer manufacturer evaluation guide.
Get a dryer selection & budget quotation
Tell us what you need to dry, your required capacity and installation country. Share inlet and target moisture, available heat and project timing if known. Estimates are welcome; write “not sure” where you need guidance. Our team can review suitable dryer options and the information needed for a budget quotation. Final selection and pricing depend on your material and project requirements.
Prefer to discuss first? WhatsApp +91 98311 73874 or contact Gem Drytech.
Related sludge drying projects
Start with the gelatin filter-press sludge case below for a published BELTOTHERM belt-dryer installation in Kerala. The sticky bio-sludge case describes a BELTOTHERM system for a paper mill in Gujarat. Each case identifies its own material, process and reported results; compare those conditions with your project when discussing dryer selection.
These projects illustrate different sludge challenges. Equipment selection and results depend on the feed and process requirements of each project.

